Report
Question
CO2 cylinder gas for MAG welding has 90 bar the internal pressure. Compute the welding time can be used the cylinder, if the flow rate is 12 L/min and the net wet of gas about22Kg
CO2 cylinder gas for MAG welding has 90 bar the internal pressure. Compute the welding time can be used the cylinder, if the flow rate is 12 L/min and the net wet of gas about22Kg

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
10 months 1 Answer 9 views Beginner

Report
Question
A portion of the square plate is loaded by a 20 lb / f * t ^ 2 distributed pressure load. Determine the coordinates at which the resultant passes though the x-y plane
A portion of the square plate is loaded by a 20 lb / f * t ^ 2 distributed pressure load. Determine the coordinates at which the resultant passes though the x-y plane

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
10 months 1 Answer 6 views Beginner

Report
Question
A portion of the square plate is loaded by a 20 lb / f * t ^ 2 distributed pressure load. Determine the coordinates at which the resultant passes though the x-y plane
A portion of the square plate is loaded by a 20 lb / f * t ^ 2 distributed pressure load. Determine the coordinates at which the resultant passes though the x-y plane

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
10 months 1 Answer 6 views Beginner

Report
Question
4. Bar ABC shown in Figure 4 is made from plastic having modulus of elasticity, E = 4.0 GPa. The bar consists of two segments, AB and BC. The diameter of segments AB and BC are d1 = 100 mm and d2 = 60 mm, respectively. A longitudinal hole of diameter d is drilled through segment AB for one half of its length (250 mm). If the shortening (contraction) of bar ABC is limited to 8.0 mm, determine; i. Draw the free – body diagram (F.B.DO and determine the deformation of segment BC. (4 marks) ii. Calculate the maximum allowable diameter dmax of the hole. (6 marks)
4. Bar ABC shown in Figure 4 is made from plastic having modulus of elasticity, E = 4.0 GPa. The bar consists of two segments, AB and BC. The diameter of segments AB and BC are d1 = 100 mm ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
10 months 1 Answer 11 views Beginner

Report
Question
. Design the longitudinal and circumferential joint for a boiler whose diameter is 2.4 metres and is subjected to a pressure of 1 N/mm2. The longitudinal joint is a triple riveted butt joint with an efficiency of about 85% and the circumferential joint is a double riveted lap joint with an efficiency of about 70%. The pitch in the outer rows of the rivets is to be double than in the inner rows and the width of the cover plates is unequal. The allowable stresses are: σt = 77 MPa ; τ = 56 MPa and σc = 120 MPa. Assume that the resistance of rivets in double shear is 1.875 times that of single shear. Draw the complete joint
i need explanation

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
10 months 1 Answer 12 views Beginner

Report
Question
Group Assignment #1: Assembly Language Referring to the given title below for each group, you need to: 1. Provide a simple algorithm/flowchart to solve the given problem Notes: The n is a user input value and must be at least >15. 2. Create a C code based on the given specification with some input test stimulus and make sure the result is correct. 3. Create an equivalent assembly program based on ARM Instructions (your program must use the concept of subroutine and program control to carry out the necessary CPU operations, instead of full and lengthy sequential instructions). 4. Provide a video to explain your coding by debugging the assembly code in (3) line by line in the Keil uVision software, using the same input test stimulus in (2) to prove it generates the same computation result. Question 1: Compute the greatest common divisor (GCD) of two positive numbers.
Group Assignment #1: Assembly Language Referring to the given title below for each group, you need to: 1. Provide a simple algorithm/flowchart to solve the given problem Notes: The n is a user input value and must be at least >15. 2. Create a ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
0
10 months 0 Answers 6 views Beginner