Report
Question
Ask a this problem, we study the idea of mixing in a superheterodyne receiver. To be specific, consider the block diagram of the mixer shown in the figure that consists of a product modulator with a local oscillator of variable frequency f _l, followed by a band-pass filter. the input signal is an AM wave of bandwidth 10 kHz and carrier frequency that may lie student submitted image, transcription available below and you will be sure to find an answer!
this problem, we study the idea of mixing in a superheterodyne receiver. To be specific, consider the block diagram of the mixer shown in the figure that consists of a product modulator with a local oscillator of variable ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
solved 0
9 months 1 Answer 8 views Beginner

Report
Question
Exercise 3.3 (HW) In a PCM system, the message sample are encoded with 4 bits per samples. If the minimum sampling rate used is 8 kHz, calculate the following: (i) Frequency of the information signal; (ii) Number quantization level; (iii) Transmission rate; (iv) Transmission bandwidth. student submitted image, transcription available below
Exercise 3.3 (HW) In a PCM system, the message sample are encoded with 4 bits per samples. If the minimum sampling rate used is 8 kHz, calculate the following: (i) Frequency of the information signal; (ii) Number quantization ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 5 views Beginner

Report
Question
The PCM samples are encoded into a 4-bits system. If the minimum sampling rate used is 8kHz, calculate a) The quantization level. b)the transmission rate(2 sample’s) c) The transmission bandwidth 2- Let us consider an example that relates the Nyquist and Shannon formulations. Suppose that the spectrum of a channel is between 3 MHz and 4 MHz and SNR = 24DB I need the answer as soon as possible Please. student submitted image, transcription available below a question and you will be sure to find an answer!
The PCM samples are encoded into a 4-bits system. If the minimum sampling rate used is 8kHz, calculate a) The quantization level. b)the transmission rate(2 sample's) c) The transmission bandwidth 2- Let us consider an example that relates ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
solved 0
9 months 1 Answer 5 views Beginner

Report
Question
Determine the percentage increase in power capacity made possible in changing over from a flat belt drive to a V-belt drive. The diameter of the flat pulley is same as the pitch diameter of the grooved pulley. The pulley rotates ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 8 views Beginner

Report
Question
One input to the conventional AM modulator is a 500kHz carrier with an. amplitude of 20 V_p. The second input is a 10kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of plusminus 7.5V_p. Determine: (a) Upper and lower sid a a and you will be sure to find an answer!
One input to the conventional AM modulator is a 500kHz carrier with an. amplitude of 20 V_p. The second input is a 10kHz modulating signal that is of sufficient amplitude to cause a change in the output wave ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 8 views Beginner

Report
Question
carrier wave of frequency 100MHz is frequency-modulated by a sinusoidal wave of amplitude 20V and frequency of 100kHz. The frequency sensitivity of the modulator is 25kHz/V. (a) Determine the approximate bandwidth of the FM wave using Carson’s rule. (b) Determine the bandwidth obtained by transmitting only those side frequencies with amplitudes that exceed student submitted image, transcription available below a question and you will be sure to find an answer!
carrier wave of frequency 100MHz is frequency-modulated by a sinusoidal wave of amplitude 20V and frequency of 100kHz. The frequency sensitivity of the modulator is 25kHz/V. (a) Determine the approximate bandwidth of the FM wave using Carson's rule. ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 9 views Beginner

Report
Question
Figure shows the block diagram of a wideband frequency modulator using the indirect method. This modulator is used to transmit audio signals containing frequencies in the range of 100 Hz to 15 kHz. The narrowband phase modulator is supplied with a carrier of frequency f1 = 0.1 MHz by a crystal-controlled oscillator. A second crystal. controlled oscillator student submitted image, transcription available below a question and you will be sure to find an answer!
Figure shows the block diagram of a wideband frequency modulator using the indirect method. This modulator is used to transmit audio signals containing frequencies in the range of 100 Hz to 15 kHz. The narrowband phase modulator is ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
solved 0
9 months 1 Answer 7 views Beginner

Report
Question
Design a shaft and flange for a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. The following data is available for design: Power of engine = 75 kW; speed of engine = ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 2 Answers 9 views Beginner

Report
Question
EN-US

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 11 views Beginner

Report
Question
A 380mm x 380mm concrete column which is pin connected at both ends has an unsupported length of 4.9m. The column is carrying a total factored axial load Pu = 520 kN and a lateral concentrated load of 240 kN ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
in progress 0
9 months 1 Answer 6 views Beginner