Answer this
ReportQuestion
hokage69
Answer this
The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a diameter of 25 mm. If it is fixed at its ends A and B and subjected to a torque of 750 N.m, determine the maximum shear stress in the shaft. Given Gst = 75 Gpa.
ReportQuestion
Amirin
The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a diameter of 25 mm. If it is fixed at its ends A and B and subjected to a torque of 750 ...
Please briefly explain why you feel this question should be reported.
A rolled-steel shape is used with the support and cable arrangement shown. Cables BC and BD are taught and prevent motion of point B in the xz plane. Knowing that L=5 m, determine the allowable centric load P. Use E = 70 GPa, Ix = 50×10^6 mm^4, Iy = 5×10^6 mm^4
ReportQuestion
vthg99
A rolled-steel shape is used with the support and cable arrangement shown. Cables BC and BD are taught and prevent motion of point B in the xz plane. Knowing that L=5 m, determine the allowable centric load P. Use E ...
Please briefly explain why you feel this question should be reported.
A storm with 10 cm precipitation produced a direct runoff of 5.8 cm. Given the time distribution of the storm as below, estimate the & index of the storm.
ReportQuestion
Ghulam Mustafa
Urgently nee sir please
A storm with 10 cm precipitation produced a direct runoff of 5.8 cm. Given the time distribution of the storm as below, estimate the & index of the storm.
Please briefly explain why you feel this question should be reported.
Determine the vertical displacement at point A of the steel beam (E = 200 Gpa, I = 9.5*10^6 mm^4), represented in the figure, using the energy method (Energy Conservation and/or Castigliano’s Theorem), when w = 10 kN/m
ReportQuestion
vthg99
Determine the vertical displacement at point A of the steel beam (E = 200 Gpa, I = 9.5*10^6 mm^4), represented in the figure, using the energy method (Energy Conservation and/or Castigliano's Theorem), when w = ...
Please briefly explain why you feel this question should be reported.
Each member of the truss shown in Fig. 2b is made of steel and has a uniform cross section area os 1200 mm2. Use the principle os conservation of energy to determine the vertical deflection of joint C caused by the aplication of the 200 kN load. Take E = 200 GPa.
ReportQuestion
vthg99
Each member of the truss shown in Fig. 2b is made of steel and has a uniform cross section area os 1200 mm2. Use the principle os conservation of energy to determine the vertical deflection of joint C caused by ...
Please briefly explain why you feel this question should be reported.
Heat Transfer
ReportQuestion
Therichkid
The heat transfer co
-
efficient h depends on the buoyancy force per unit mass
(
gBT
)
,
The density of fluid
(
p
)
,
the fluid layer of thickness L and the viscosity
(
u
)
,
the thermal conductivity K and the specific heat capacity Cp
.
show that the Nussert number is a function ...
Please briefly explain why you feel this question should be reported.
Heat Transfer
ReportQuestion
Therichkid
The heat transfer co
-
efficient h depends on the buoyancy force per unit mass
(
gBT
)
,
The density of fluid
(
p
)
,
the fluid layer of thickness L and the viscosity
(
u
)
,
the thermal conductivity K and the specific heat capacity Cp
.
show that the Nussert number is a function ...
Please briefly explain why you feel this question should be reported.
shows Inflow and Outflow hydrographs for certain reach of a channel. Find the Muskingum’s Coefficients ‘X’ and ‘K’ and route the given inflow hydrograph.
ReportQuestion
Ghulam Mustafa
shows Inflow and Outflow hydrographs for certain reach of a channel. Find the Muskingum's Coefficients 'X' and 'K' and route the given inflow hydrograph.
Please briefly explain why you feel this question should be reported.
Jackscrew
ReportQuestion
Ahmed alhebsi
A jackscrew is used to raise and lower a 100-kg block as shown in below figure. The screw has a pitch
P = 15 mm, mean radius r = 10 mm, and is single-threaded. The coefficient of static friction between